降低安裝通風管道的成本有哪些有效措施？

發布人：http://www.hkcts.com.cn   發布時間：2017-10-19 13:07:05

風管組裝：風管較短可以一次性在地面組裝，風管較長可依據安裝場地情況分段組裝。組裝時應盡量調整風道的中心度和水平度，避免風管扭曲或上下起波，左右擺龍，每段風道不宜超過10m。組裝時，墊片應墊平，法蘭螺栓應均勻擰緊，螺母帽均朝向同一方向

Air duct assembly: the wind pipe is short, can be assembled on the ground at one time, the wind pipe is long, can be assembled according to the installation site. When assembling, the center and levelness of the air duct should be adjusted as much as possible so as to avoid the distortion or upward and downward wave of the wind pipe and the left and right swing, and each section of the air duct should not exceed 10m. When assembled, the gasket pad, the flange bolts should be tightened evenly, nuts are toward the same direction

風管就位：先檢查全部支架的水乎度、標高、牢固程度。風管就位一般使用直接和吊具兩種方式。如果風管斷面較小位置又很低的可采用人工就位方法，只需搭設簡易腳手架即可。當風管斷面較大且管段較長時，可采用滑輪、倒鏈、大繩等方法吊裝。

Air pipe in place: first check the water level, elevation, firmness of all the supports. Two ways of direct and hanger are used in the air pipe. If the cross section of the duct is small and the location is very low, the manual placement method can be used, and only a simple scaffold can be built. When the cross section of the air duct is large and the pipe section is longer, the pulley, the chain and the big rope can be used for hoisting.

為了便于風道就位，一般多采用將風道吊在腳手架上，然后再將其抬放在風道支架上的方法。腳手架應沿其風道長度方向搭設，高度和位置應適合施工操作，吊裝順序應先干管后支、立管。

In order to make the air duct in place, it is generally used to hang the air duct on the scaffold, and then put it on the support of the air duct. The scaffold shall be erected along the length of the air duct, and the height and position shall be suitable for the construction operation. The lifting sequence shall be dried, supported and supported.

風道調直：就位在支架上的風道，應撥正位置，調整風道橫平豎直，然后再按圖集要求固定。

Duct straightening: in place on the support of the air duct, should adjust position, adjust the air duct vertically, then according to the requirements of atlas fixation.

就現階段來看，我國國內建筑通風管道類型多使用鍍鋅鋼板風管，但是，種種案例與科研數據顯示，鋼板風管的耐火性能并不理想，為了改善防火性能，可以將防火材料包覆在鋼板風管表面，通過這一方式可以達到1～2h防火性能，這樣即可滿足防排煙管道設計需求。

At this stage, China's domestic construction ventilation pipe type multi use galvanized steel duct, however, all cases and research data show that the fire-resistant performance of wind pipe plate is not ideal, in order to improve the fire performance, fire prevention materials can be coated in the surface of steel duct, through this way can reach 1 ~ 2H fire the performance, so you can meet the design requirements of smoke exhaust pipe.

根據我國《建筑防排煙系統技術要求》的相關規定，為了保障排放管的防火效果，排煙管在穿越防火區域以及排煙管道吊頂時，需要控制好管道耐火極限，一般情況下，耐火極限必須要保持在1h以上；同時，排煙管道應該禁止穿越樓梯間與建筑物的前室，如果穿越出現困難，就需要調整耐火極限，將極限控制在2h以上。

According to the relevant provisions of China's "building protection requirements" exhaust system technology, in order to ensure the effect of fire discharge pipe, the exhaust pipe in the exhaust pipe through fire area and ceiling, the need to control the pipeline fire resistance, under normal circumstances, the fireproof limit must be maintained at more than 1h; at the same time, the exhaust pipe should be banned across the front stairs between the buildings, if through the difficulties, we need to adjust the fire resistance limit, the limit control over 2h.